Joined: 19 May 2008 Posts: 656 Location: Perth - SOR
Posted: Sat Jun 28, 2008 2:56 pm Post subject:
auto couture, very nice. size is slightly irrelevant to fitment, offsets are what you need to know. anyways, 9.5 is a little large up front but will work especially if you dont go too low otherwsie they might scrub your guards liners and things. tyres look nicely stretched so that is a positive.
EDIT - okay found them, 19x9.5 +17 19x10 +4. those offsets are too low unless you are going to go rolled and pulled/flared guards, plus stretched tyres and max camber. up to you though, i would buy them if you like them and make them fit, but it wont be bolt on drive away kind of stuff...
Joined: 25 Apr 2007 Posts: 1092 Location: Bayswater Victoria
Posted: Sat Jun 28, 2008 3:02 pm Post subject:
Sale cutting haute couture シ…プレム it is deep rim 9.5J10J rare size
Here it what it says
If you can understand it?
Sale cutting haute couture シ…プレム deeply the rim & rare size 9 5J10J 19 inch * they are 4 these sets.
State entirely is clean, but in the joint of the rim there is the clearing floating and 1 reverse side rim repair mark (photograph reference)
There is no pain which becomes other things and matter of concern.
The ガリ scar which is conspicuous, there is no kind of trouble which is hindrance, in use such as distortion and air leak clearing peeling of the rim.
As for size the front (LO disk) as for 9 5J offset + 17 rear 10J offsets + 4 PCD it becomes 5 holes of 114 3.
You had used for the ローダウン 33 seaming machine.
Please inspect on the basis of size in regard to matching
The tire is front PIRELLI P - ZERO 225/40 - 19 rear BRIDESTONE T ` s - 02245/35 - 19, as for remainder of the tire there is also one wear, but you think as enabled still. At the picture judgement in regard to the detailed remaining groove.
How to think the privacy - Condition of Use - premium member code - guideline - help inquiry
Copyright (C) 2008 Yahoo Japan Corporation. All Rights Reserved. _________________
289rwkws 17psi 12.9 @ 115 mph standard twins standard stall.
Trying to be the fastest stock twin turbo aristo in OZ
Joined: 19 May 2008 Posts: 656 Location: Perth - SOR
Posted: Sat Jun 28, 2008 3:08 pm Post subject:
yeah i edited my post, i found them. i would suggest the offsets are a bit over hte top for you.
i like these Leon Hardiritts, and the sizing and offsets is good, though im not sure about the Super Lo Disc on the fronts as far as brake clearance goes.. but these are much more expensive ($~2600 landed with tyres), but these exact wheels are $3600 new no tyres (priced them up)
Joined: 19 May 2008 Posts: 656 Location: Perth - SOR
Posted: Sat Jun 28, 2008 3:17 pm Post subject:
i just think they will be a bit aggressive is all.
i dont know how much you want to do to the car, but to get 9.5 +17 up front it will need stretched tyres such as 225/35 and will take rolling and probably some pulling of the guard, plus low ride height in order to acheive natural camber to tuck them in. at this ride height and width, you will probably need to remove your inner guard liners and move your wiring harness up higher.
to fit 10 +4 up the back, you will need to run some nice stretch such as 235/35 along with low ride height and maximum natural camber. you will also need to roll and probably pull the guards.
all of the above rolling and pulling could cause paint damage too. so if you are cool with doing this i recommend doing it! cause it will look fat as. but they will be a fairly difficult wheel to fit in these specs i would say
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum